Lightning Protection System: Components, Standards and Design Basics
Navdeesh Kandhari
6 minutes reading
Nov 17, 2026

India sees some of the highest lightning activity in the world, and a direct strike on an unprotected building can start fires, crack structures and destroy electrical equipment. A lightning protection system (LPS) gives that current a safe, planned path to the ground. This guide explains the three parts every LPS needs, the standard that governs it in India, and the choices you will face when specifying one.
What a lightning protection system does
An LPS does not prevent lightning. It intercepts a strike before it hits the structure, carries the current down the outside of the building, and disperses it into the earth without damage. If any one of its three parts is missing or poorly installed, the other two cannot do their job.
The standard: IS/IEC 62305
India has adopted the international standard IEC 62305 as IS/IEC 62305. It has four parts:
Part 1: General principles.
Part 2: Risk management, which decides whether a structure needs protection and at what level.
Part 3: Physical damage to structures and life hazard, which covers the LPS itself.
Part 4: Electrical and electronic systems within structures, which covers surge protection.
The risk assessment in Part 2 sets a Lightning Protection Level (LPL I to IV) and a matching LPS class. Class I is the most stringent. The class decides spacing, mesh sizes and inspection intervals throughout the design.
Component 1: Air termination system
The air termination system is what the lightning actually strikes. It sits at the highest and most exposed points of the structure: roof edges, corners, parapets, towers and rooftop equipment. It can be made of vertical air rods, horizontal conductors laid as a mesh, or a combination. Designers place it using one of three methods: the rolling sphere, the protection angle, or the mesh method.
Conventional air terminals vs ESE arrestors
Early Streamer Emission (ESE) arrestors claim a larger protection radius than conventional rods by triggering an upward streamer earlier. They are designed to the French standard NF C 17-102 and are not part of IEC 62305. Many projects in India do specify them, but you should check which standard your project, consultant or insurer follows before choosing between the two.
Component 2: Down conductors
Down conductors carry the current from the air termination to the earth termination by the shortest, most direct route. They are usually GI or copper strips or tapes fixed to the outside of the building. IEC 62305-3 sets typical spacing between down conductors around the perimeter by LPS class:
LPS class | Typical down conductor spacing |
|---|---|
I | 10 m |
II | 10 m |
III | 15 m |
IV | 20 m |
Each down conductor should have a test joint just above ground level, so the earth electrode can be disconnected and tested.
Component 3: Earth termination system
The earth termination disperses the current into the soil. It is usually made of earth rods, earthing strips run as a ring, earth pits and their connections. IEC 62305-3 recommends an earth resistance below 10 ohms where possible. The electrode material matters because it is buried for decades: copper bonded rods resist corrosion better than GI in most soils, while GI remains a cost-effective choice for shorter-life installations.
Bonding and surge protection
A complete design also bonds metal services (water pipes, cable trays, structural steel) to the LPS so that no dangerous sparks jump between them, and adds surge protective devices to protect electrical and electronic systems inside the building. These are covered in IEC 62305-3 and Part 4.
Inspection and maintenance
LPS class | Visual inspection | Complete inspection |
|---|---|---|
I and II | Every 1 year | Every 2 years |
III and IV | Every 2 years | Every 4 years |
Inspect after any known strike as well. Check for loose fixings, broken conductors, corroded joints, and earth resistance at each test joint.
What we make and what we supply
At SS Engineering Works we make earth rods and earthing strips in Sonipat. We supply ESE arrestors, exothermic welding systems, earthing enhancement compound and FRP pit covers from trusted partners. We label every product clearly as made or supplied.
Frequently asked questions
Is a lightning arrester the same as a lightning protection system?
Not exactly. In building work, 'lightning arrester' usually means the air terminal on the roof, which is only one part of an LPS. A complete system also needs down conductors and an earth termination.
Does an ESE lightning arrester need earthing?
Yes. Every air terminal, including ESE devices, must connect through down conductors to a properly designed earth termination, or the system cannot discharge the strike safely.
How often should a lightning protection system be inspected?
Under IEC 62305-3, Class I and II systems need a visual inspection every year and a complete inspection every two years. Class III and IV need them every two and four years respectively.
Planning an LPS? Share the building height, roof type and soil conditions with us. Send your requirement on WhatsApp: +91 7065337337, or browse the range on ssengineeringwork.in.