Hex and Square Bright Bars: Sizes, Grades and Uses

Navdeesh Kandhari

6 minutes reading

Nov 19, 2026

Hexagonal and square bright steel bars showing their profiles, sizes and dimensions for industrial engineering and machining applications.

Round bars get most of the attention, but a large share of machined components start life as hex or square bright bars. Using the right section from the start saves machining time, material and tooling. This guide explains how hex and square bright bars are made, how their sizes are measured, which grades are common, and where each section is used.


Why start with a shaped bar?

If the finished part has flats, such as a nut, a fitting or a key, starting from a bar that already has those flats removes whole machining operations. A hex fitting made from hex bar only needs turning, drilling and threading. Made from round bar, it would also need six flats milled. Over thousands of parts, that difference is significant.


How hex and square bright bars are made

Like round bright bars, hex and square bars are cold drawn. A hot rolled bar is cleaned of scale and pulled through a hardened die shaped to the final section. This gives an accurate size, sharp and consistent flats, a clean bright surface and higher strength from the cold work. Unlike round bars, shaped bars cannot be finished by peeling or centreless grinding, so the quality of the drawing die and process is everything.


How sizes are measured

  • Hex bars are measured across flats (AF): the distance between two opposite flat faces. This matches the spanner size of the finished part.

  • Square bars are measured by the side of the square.

  • Both have small rounded corners. Corner radius matters if your part needs a sharp edge.


Common sizes

Hex bar sizes usually follow standard spanner sizes so that finished nuts and fittings fit standard tools.

Section

Commonly used sizes (mm)

Hex (AF)

10, 13, 17, 19, 22, 24, 27, 30, 32, 36, 41, 46, 50

Square (side)

6, 8, 10, 12, 16, 20, 25, 32, 40, 50

SS Engineering Works draws round, square and hex bright bars across a range of 2 to 100 mm. Ask us about your exact size.


Tolerances

Drawn hex and square bars are most commonly supplied to h11 tolerance, while round bars are often drawn to h9 or h10. The tolerance class tells you how far below the nominal size the bar can be. If your part needs a closer fit on the flats, say so on your order.


Common grades

Grade

Type

Where it is used

EN 1A

Free cutting steel

High-volume turned parts such as fittings and adapters, where fast machining matters more than strength

EN 8

Medium carbon steel

Bolts, studs, couplings and parts that need more strength

EN 19

Chromium molybdenum alloy steel

High-tensile fasteners and heavily loaded parts, usually heat treated

SS Engineering Works draws round, square and hex bright bars across a range of 2 to 100 mm. Ask us about your exact size.


Where hex bright bars are used

  • Hex nuts, bolts and special fasteners

  • Hydraulic and pneumatic fittings, adapters and unions

  • Plumbing and gas fittings

  • Spacers, standoffs and machine components


Where square bright bars are used

  • Keys and keyways in shafts and pulleys

  • Machine slides, guides and tooling

  • Fabricated frames, gates and grilles that need a clean finish

  • Agricultural and automotive components


What to specify when you order

  • Section and size (AF for hex, side for square)

  • Grade

  • Tolerance class

  • Length (random or fixed) and quantity, by weight or pieces

  • Any test certificate requirements

To estimate weight, use our bright bar weight chart: a hex bar weighs AF x AF x 0.0068 kg per metre, and a square bar weighs side x side x 0.00785 kg per metre.


Hex bar or round bar: when to switch

As a rule of thumb, if more than a quarter of the machining time on a part goes into producing flats, it is worth pricing the job in hex or square bar. Shaped bars cost slightly more per kg than round, but the saving in machine time, tooling and scrap usually outweighs it on medium and high volumes. On short runs, or where only a small portion of the part needs flats, round bar may still be cheaper overall.


Quality checks when the bars arrive

  • Measure across flats at several points along a few bars to confirm size and tolerance

  • Check that the flats are straight and the corners are even, not twisted along the length

  • Look for a clean, bright surface without scale, seams or deep die marks

  • Match the grade and heat number on the bundle tag with the test certificate


Frequently asked questions

  • How is the size of a hex bar measured?

    Across flats (AF), the distance between two opposite flat faces. A 24 mm hex bar measures 24 mm across flats, which matches a 24 mm spanner.


  • Which grade is best for hex nuts and fittings?

    EN 1A free cutting steel is common for fittings where machining speed matters. EN 8 or EN 19 are used where the part needs higher strength.


  • What is the difference between a hex bar and a hex rod?

    Nothing. Both terms describe a bar with a hexagonal cross-section. 'Bright hex bar' means it has been cold drawn to size with a clean finish.


Need round, square or hex bright bars? Tell us the section, size, grade and quantity. Send your requirement on WhatsApp: +91 7065337337, or browse the range on ssengineeringwork.in.