Earth Resistance Testing: Methods, Recommended Values and How Often to Test

Navdeesh Kandhari

6 minutes reading

Nov 16, 2026

Earth resistance testing using a digital earth tester and copper-bonded earthing electrode to measure grounding system resistance.

An earthing system that passed its test at commissioning is not guaranteed to pass today. Soil dries out, joints corrode and buildings change around it. Regular earth resistance testing is the only way to know whether your earthing will actually carry fault current safely when it needs to. This guide covers what you are measuring, the main test methods, the values commonly targeted in India, and what to do when a reading is too high.


What earth resistance means

Earth resistance is the resistance, in ohms, between your earth electrode and the general mass of the earth. The lower it is, the more easily fault current and lightning current can flow into the ground instead of through equipment or people. It depends on three things: the electrode itself, the connections, and above all the soil around it.


Why earth resistance changes through the year

  • Moisture: wet soil conducts far better than dry soil. Readings taken during or just after the monsoon look better than the system really is.

  • Temperature: frozen or very hot, dry ground raises resistance.

  • Salts and minerals: these are slowly leached out of the soil by rain, especially around older pipe earthing.

  • Corrosion: rusted joints and clamps add resistance even when the electrode is fine.

  • Site changes: new concrete, paving or drainage can cut off moisture to a pit.

This is why the most honest reading is taken in the driest part of the year.


Earth resistance test methods

1. Fall of potential (three point) method

The standard method for testing a single electrode or small system. The electrode under test is disconnected from the installation. A current spike is driven into the ground some distance away and a potential spike is placed between the two, typically at about 62 percent of the distance to the current spike. The tester passes current and reads the resistance. Moving the potential spike a little either side and getting similar readings confirms the result is valid.

2. Clamp-on method

A clamp-on tester measures resistance without disconnecting the electrode or driving spikes. It is quick for routine checks on systems with several parallel electrodes, but it does not work on a single isolated electrode, and it can mislead if the return path is not what you assume.

3. Soil resistivity (Wenner four point) test

This test measures the soil itself rather than an electrode. Four spikes are placed in a straight line at equal spacing. It is done before designing a new earthing system, to decide electrode type, length and number.


Recommended earth resistance values

There is no single number that applies to every installation. The values below are targets commonly used in Indian practice. Your system designer or the project specification has the final word.

Installation

Commonly targeted value

Power stations

0.5 ohm

EHT substations

1 ohm

33 kV substations

2 ohms

Distribution transformer structures

5 ohms

Transmission tower foot

10 ohms

Lightning protection earth termination (IEC 62305-3)

Below 10 ohms recommended


How often should you test?

  • At least once a year, ideally in the driest month.

  • After any major construction, excavation or paving near the earth pits.

  • After a lightning strike or a significant electrical fault.

  • Whenever equipment shows unexplained tripping, shocks or surge damage.

Keep a simple log: date, pit number, method, reading and weather. A rising trend tells you more than any single reading.


What to do if your earth resistance is too high

  • Check the joints first. Clean, tighten or replace corroded clamps and connections. This is the cheapest fix and often the right one.

  • Treat the pit. Low-resistivity backfill compound around the electrode reduces contact resistance and holds moisture.

  • Go deeper. A longer rod can reach permanently moist soil layers.

  • Add electrodes in parallel. Space additional rods at least one rod length apart, ideally two, so they do not share the same soil.

  • Upgrade the electrode. Copper bonded rods resist corrosion better than GI in most soils, so readings stay stable for longer.


Frequently asked questions

  • What is an acceptable earth resistance value?

    It depends on the installation. Commonly used targets in India range from 0.5 ohm for power stations to 5 ohms for distribution transformer structures. For lightning protection, IEC 62305-3 recommends below 10 ohms.


  • How often should earth resistance be tested?

    At least once a year, preferably in the driest season, and again after construction work nearby, a lightning strike or a major fault.


  • Can I test earth resistance with a multimeter?

    No. A multimeter cannot measure earth resistance reliably. Use a proper earth resistance tester with the fall of potential or clamp-on method.


Readings creeping up? We supply earth rods, earthing strips and pit accessories for repairs and upgrades. Send your requirement on WhatsApp: +91 7065337337, or browse the range on ssengineeringwork.in.